Choker necklace tutorial inspired by Cousin products

2

   tutneckfinished

In this new jewelry tutorial we will be making a choker necklace with a pendant drop that has a beaded link chain attached. This creates an even more elegant look than with just a simple choker. This will fit a 12 1/2 – 15 1/2 inch neck with its adjustable extender chain. Feel free to use some of what you have at home and create in the colors that you love. I love the gothic and sultry feel of red and black!

This is some of what we’ll need:

tutneckwhatyouneed

A 12 inch length of black grosgrain ribbon, a pendant with both a north and south loops, heavy large oval link black chain, lighter weight circle link black chain, 8mm red beads, 25mm ribbon end crimps,  oval black jump rings, black large sliding bail, black lobster clasp, 20 gauge black wire and an optional charm for the tip of the extender chain. You will also need wire cutters, 2 long nose pliers, round nose pliers, scissors and a gel super type glue.

tutneckendcrimpandpendantcol

You will begin your necklace by cutting a 12 inch section of your ribbon and sliding the bail to the center of the ribbon. Attach the north end of the pendant with an oval jump ring to the bail loop. At each end of the ribbon you will need to attach your end crimps. Apply a small amount of glue to the inside of the end crimp and center the ribbon inside. Squeeze the end crimps closed tightly with your long nose pliers.

tutneckwirecol

Begin to wire wrap your beads into links. Cut your wire into 2 1/2 – 3 inch lengths and create a wrapped loop at one end cutting off the excess. String your bead down the wire to your loop, make a wire wrapped loop at the opposite end and cut off the excess.  You will need about 12 of these.

tutnecklinkscol

Separate the heavy chain links with your long nose pliers. You will need 12 closed links. Attach the first link to the south end of your pendant with an oval jump ring. Alternate your bead links and chain links with oval jump rings equally on each side of the pendant making 2 strands.

                 tutnrckclaspcol tutneckdangle

Attach the lobster clasp to the end crimp on one side of your ribbon with a couple jump rings. Use about an inch of the lighter black chain and connect one end of it to the end crimp with a lobster clasp and the other end of it to the beaded chain you created. On the other side, connect a 3 inch section of the same chain to serve as an extender chain to the end crimp with an jump ring and repeat attaching the other end of your beaded chain. You can then attach a charm if you choose to the end of the extender chain so you can look awesome coming and going.

tutnecktopvw

Your necklace is now completed and it was easy!

A special thank you to Cousin Corporation for some awesome supplies to inspire me.

Thanks for learning, reading and following the Freak Show!

Advertisements

Basic charm bracelet tutorial inspired by Cousin brand products: Part Two

0

Part Two: Putting it all together

pirpleflowerbracewirewraptutorial

Lets make some charms!

Buying only already made charms limits your creativity and can be costly. Making your own beaded charms allows you to incorporate many color options and a uniqueness to your own one of a kind bracelet.

It’s very simple to create these like the ones pictured above that I created for this bracelet. Use a ball or head pin to stack your small beads, bead caps and large beads onto. When you have the configuration how you like it, wrap the wire left at the top around the end of a round tip plier, leaving a few millimeters space under it (shown above) and hold the wire at the tip with your long nose pliers.

purplecharmwirewrapcharmtutorial

Holding the loop you have made securely with your round nose pliers, begin to wrap the wire around the space of wire under it with your long nose pliers in a spiral downward. When you have finished your spiral, use the flush cutters to cut off any excess wire.

Now we are ready to start configuring our bracelet and yes, this requires a little basic math but that is what keeps the bracelet balanced.

purpleflowerbracetlayouttutorial

Now I know this looks like a mess but it’s a blueprint, a grand plan for balance! I recommend taking a picture as a reminder of how you wanted it because when we clear them out to begin attaching the charms, sometimes even I forget the order I had planned.

Lay your chain down on your bead mat and attach it to your mat right below the lobster clasp to hold it in place with a pin. Measure out about 6-7 inches down from the clasp and secure it right there with your other pin. This is your canvas to create in so begin to lay out your charms on both sides in a pattern that you feel gives a good balance and continuity to your bracelet. Now, here comes the math! Count how many links in the chain there are within the area you have pinned, then count how many charms you have on one side of this chain. Is there enough for each link? Or is there just enough for you to skip one link or two links in between each charm? If it’s an odd number then you should look at the charms your using and see if there is a wider charm that could take up the slack by skipping one before and one after just this wider charm. It’s just a little basic math and anyone can configure it. After you do this with one side, do the same configuration for the other.

Now you are ready to attach the charms!

purplecharnattachcharmtutorial

This is the final part! Open your jump ring and place the charm on the jump ring first and then attach it to the chain link using both long nose pliers to close them up in order according to your blueprint using your final equations. Do one side at a time making sure to secure close each and every jump ring. I prefer oval jump rings because the split is on the side of the oval so when the charm hangs, it doesn’t hang on the part where you close it and there is less chance of losing your charm if it gets caught on something. You may want to consider a little bead or charm dangle for the tip of the extender chain for a finished look. The bracelet you have made is adjustable and can now be worn by anyone from 6 3/4 to 8 inches long.

purplecharmfinishtopvw        purplecharmfinishclsup

purplecharmfuulltopvw

Thank you for reading and learning. I’ll be back soon with another tutorial!

PEACE!

Basic charm bracelet tutorial inspired by Cousin brand products: Part One

0

Part One: Getting Started

purplecharmfinishtopvw

This is the first tutorial I’ll be doing here on my blog so I’m excited to share a little of my Freak Show methods with you! Having been an only child, my mother had to work extra hard at teaching me to share and I believe she was successful. In a jewelry industry full of artists that are completely secretive about their methods, I plan to be different and share and share alike. This isn’t rocket science or a magic formula, this is FUN! So, if you like what your learn and have the opportunity, share the fun with someone else out there and teach them too!

I will be doing this in two parts and this is first part.

Charm bracelets seem to be a top seller in my Etsy shop and are the most requested type custom order I create. Usually these bracelets tell a story when I make them but for this tutorial, lets just begin with some basic lovelies to get started.

purpleandflowercharmbracematerials

Above you will see the items I used in the piece and many of them are Cousin brand. I know it looks like a lot of stuff and it is but these are VERY basic, easy to acquire jewelry findings, beads and charms. Feel free to use similar items and colors that YOU love. Sizes aren’t very important here. While one person likes a big and chunky piece, another may enjoy something on the lighter side. Although, the balance of the items used and the technique in which you build the bracelet is very important for the final product.

Here is what I used:

A variety of great purple acrylic and mesh beads from Cousin

Gunmetal circle link textured chain from Cousin

Purple cracked glass beads

Gunmetal flower beads

AB crystal teardrops

Crystal AB rondelle and bicone beads

Faceted metallic beads

A variety of bead caps

Gunmetal head pins, ball pins and decorative head pins

A variety of gunmetal and silvertone flower charms

Tiny AB flatback crystals

Gunmetal oval jump rings

Gunmetal lobster clasp

You will also need a bead mat, a couple of pins, a ruler, an etcher (optional), a jewel picker, a toothpick, a super fast drying gel type glue, a flush wire cutter, 2 long nose pliers and a round tip plier. I use the Cousin brand tools for my work and that’s is what you see pictured.

purpleflowerbracerystalsettingtirtorial

The first thing I need to do for this piece is set the tiny crystals into these flower charms. Whenever gluing something to metal, it’s important to rough up the exact surface area of it. I used a diamond tipped etcher to rough up the inside of these little bezels where the crystals will go before I begin gluing. I use a “superglue” gel type of glue to set crystals because honestly, jewelers glue takes too long to dry and this type of glue holds even better. I really don’t think one brand is better than the other but do make sure you are using the gel type. Use a toothpick to apply the glue into each tiny bezel area ( a little goes a long way) and then use a jewel picker to pick up each crystal to place them. A jewel picker has a sticky tip and is a must for setting crystals. This needs 10 minutes at the most to dry.

Now that you have set your crystals, you can remove a length of chain about 8 inches in length for your bracelet and use a jump ring to attach the lobster clasp.

Continue onto Part Two…